Latest updates Cisco CCDP 300-101 dumps and pdf, 300-101 Practice Questions and Answers

free exam dumps

Easily get the latest Cisco CCDP 300-101 dumps, “Implementing Cisco IP Routing (ROUTE)” 300-101 Exam.
You can upgrade your skills by downloading the 300-101 pdf or the online 300-101 exam exercise test! 99.5% pass

Table of Contents:

Latest Nicky Cisco CCDP 300-101 pdf

[PDF] Free Cisco CCDP 300-101 pdf dumps download from Google Drive:

300-101 ROUTE – Cisco:

Latest Cisco CCDP 300-101 Practice Questions and Answers

Which two statements about DMVPN are true? (Choose two.)
A. IPsec encryption not supported with statically addressed spokes.
B. t requires full-mesh connectivity on the network.
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology.
Correct Answer: AC

Where must a network engineer configure the IP helper-address command on a router?
A. On the interface that will receive the broadcasts
B. On the DHCP configuration
C. the interface that is closed to the destination DHCP server
D. on the global configuration mode
Correct Answer: A

Which NAT command do you enter to disable dynamic ARP learning on an interface?
A. R1(config-if)#ip nat enable
B. R1(config-if)#ip nat inside
C. R1(config)#ip nat serive
D. R1(config-if)#ip nat outside
E. R1(config)#ip nat allows-static-host
Correct Answer: E

Which statement describes the difference between a manually configured IPv6 in IPv4 tunnel versus an automatic 6to4
A. A manually configured IPv6 in IPv4 tunnel allows multiple IPv4 destinations.
B. An automatic 6to4 tunnel allows multiple IPv4 destinations.
C. A manually configured IPv6 in IPv4 tunnel does not require dual-stack (IPv4 and IPv6) routers at the tunnel
D. An automatic 6to4 tunnel does not require dual-stack (IPv4 and IPv6) routers at the tunnel endpoints
Correct Answer: B

Refer to the exhibit. A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the
tunnel is not coming up. What did the TAC engineer configure incorrectly?lead4pass 300-101 exam question q5

A. The crypto map is not configured correctly
B. The crypto ACL is not configured correctly.
C. The crypto map is not applied to the correct interface.
D. The OSPF network is not configured correctly.
Correct Answer: B

A network engineer wants to ensure an optimal end-to-end delay-bandwidth product. The delay is less than 64KB. Which TCP feature ensures steady-state throughput?
A. Window scaling
B. Network buffer
C. Round-trip timers
D. TCP acknowledgments
Correct Answer: A

Which option must be configured on a target device to use time stamping to accurately represent response times using
A. Responder
B. Jitter value
C. TCP Connect
D. ICMP Echo
Correct Answer: D

When unicast reverse path forwarding is configured on an interface, which action does the interface take first when it
receives a packet?
A. It checks the ingress access list
300-101 PDF Dumps | 300-101 Study Guide | 300-101 Braindumps 4 / 7
2019 Latest lead4pass 300-101 PDF and VCE dumps Download
B. It checks the egress access list
C. It verifies that the source has a valid VEF adjacency
D. It verifies a reverse path via the FIB to the source
Correct Answer: D
When a packet is received at the interface where Unicast RPF and ACLs have been configured, the following actions
Step 1: Input ACLs configured on the inbound interface are checked.
Step 2: Unicast RPF checks to see if the packet has arrived on the best return path to the source, which it does by doing
a reverse lookup in the FIB table

which the Valid range for BGP private ASNs?
A. 64512-65535
B. 62464-65024
C. 64512-65024
D. 62464-64511
Correct Answer: A

In IPv6, the interfaces running OSPF can be configured with multiple address prefixes. Which statement is true about the
IPv6 addresses that can be included into the OSPF process?
A. Specific addresses can be selected using a route map.
B. Specific addresses can be selected using an ACL.
C. Specific addresses cannot be selected for importation into the OSPF process.
D. Specific addresses can be selected using a prefix list.
Correct Answer: C

On a Frame relay, we are unable to ping the remote router, how to solve the problem?
A. DLC is active
B. DLC is not active and deleted
C. Frame Relay map is configured
D. Need an ACL to allow PING
Correct Answer: C

You want to configure a device to select an OSPF-learned route as the preferred path over an EBGP-learned route
Which action must you take?
A. Increase the OSPF cost
B. Decrease the OSPF cost
C. Increase the OSPF administrative distance
D. Decrease the OSPF administrative distance
Correct Answer: D

Which three methods can a network engineer use to fix a metric based routing loop in the network?
A. A.Implement offset lists at network boundaries
B. B. Filter routes manually using distribute lists
C. C. Filter routes manually using prefix lists
D. D. Implement proper network summarisation on key routing points
E. E. Filter routes based on tags
F. F. Utilise root database filters
Correct Answer: ABE

All of our exam dumps are updated throughout the year, follow us! Get the latest recommendations!
Pass the Cisco CCDP 300-101 exam We recommend: (854 Q&A).

Related 300-101 Popular Exam resources

title pdf youtube 300-101 ROUTE – Cisco lead4pass Lead4Pass Total Questions
Cisco 300-101 lead4pass 300-101 dumps pdf lead4pass 300-101 youtube 300-101 ROUTE – Cisco 854 Q&A
Cisco CCDP 1067 Q&A 670 Q&A 201 Q&A 140 Q&A 162 Q&A

Lead4pass Promo Code 12% Off

lead4pass 300-101 coupon

Why Choose Lead4pass?

Lead4Pass helps you pass the exam easily! We compare data from all websites in the network, other sites are expensive, and the data is not up to date, Lead4pass updates data throughout the year. The pass rate of the exam is above 98.9%.

why lead4pass 300-101 dumps